Note: These Sensors Require an M12 Extension Cable to Connect the Sensor To Your
Instrumentation. A Partial List Of Our M12 Extension Cables is Included in the Ordering Table Below.
The 3-A Approved OMEGA® PRS-TMM12 series transducers are designed for use in Sanitary or Hygienic
Clean-in-Place applications in the Food, Dairy, Beverage and BioPharmaceutical industries. These transducers are
manufactured with 316L stainless steel housings that meet the dimensional and finish requirements of 3-A Standard 74-05 and
ASME BPE-2007, and are welded and processed to provide a clean, smooth, 32 microinch or better surface finish in the wetted
areas for Clean-in-Place processes.
The probe stems are manufactured in two configurations; standard duty probes with a ¼" diameterprobe,
and a heavy duty design with a stepped 3/8" to 3/16" diameter probe design for good response times.
The OMEGA® PRS-TMM12 series transducers are identical to the PRS-M12 RTD sensors except for the addition of a
built-in 4 to 20 mA transmitter inside the housing. This eliminates the need for a separate transmitter when a 4 to 20 mA
signal is required for your instrumentation. The housing cover can be removed allowing for the adjustment of the transmitter's zero
and span settings.
There are two ranges offered as standard offerings:
The TM1M12 model ranged to provide a 4-20 milliamp output between -40 and 49°C (-40 to 120°F),
The TM2M12 model ranged to provide a 4-20 milliamp output between -18 and 93°C (0 to 200°F).
Other ranges are available as special orders, please consult our sales engineers.
A 4-Pin M12 Connector provides a quick and convenient connection point for process wiring. Simply install an M12 extension cable to
the sensor to connect it to your monitoring or control instrumentation.
Sanitary Temperature Sensor Specifications Include:
316L stainless steel process wetted surfaces with surface finishes of 32 microinches or better.
Probe lengths of 3, 4, 5 or 6 inches available from stock, other lengths available as special orders.
Standard mounting flange is 1½"-16AMP Tri-Grip in conformance with ASME BPE-2007.
4-Pin, M12 Connector.
Thermal response time of 2.5 seconds or less in water flowing at 3 ft/sec (63% response).
4 to 20 milliamp output proportional to temperature (see ranges available).
Supply Voltage 8 to 35VDC, 24VDC recommended.
Maximum temperature range is -50 to 200°C at the sensing end, 85°C max at the connector end.
† All dollar amounts on this site are shown in US currency.
Note: Please consult sales for other flange diameters, styles and probe lengths. For probe lengths longer than 6", change "-0600" in model number to the required length (example: 12" = "-1200", 9¼" = "-0925") and add $2.50 per inch to the price (up to 24 inches). Ordering Example: (1) PRS-S-0400-D1-TM1M12 Sanitary sensor with a 1/4" diameter, 4" long probe, 1-1/2"-16AMP mounting flange and integral transmitter ranged for -40 to +49°C (-40 to 120³F) Operation, $241.00
Part Number Builder
Select S for Standard Duty 1/4" Diameter H for Heavy Duty Stepped 3/8" to 3/16" Diameter
Select 0300 for 3" Probe 0400 for 4" Probe 0500 for 5" Probe 0600 for 6" Probe
Select B1 for 3/4" Flange D1 for 1 1/2" Flange E1 for 2" Flange F1 for 2 1/2" Flange G1 for 3" Flange H1 for 4" Flange
Transmitter with M12 Plug Connection
Select TM1M12 for -40 to 49C Temperature Range TM2M12 for -18 to 93C Temperature Range
NOTE: All combinations may not be valid, check spec sheet for valid part numbers.