 |
The Model CSMSTRLE is a communications and control platform
designed for use with Modular Controller Series slave modules. The
CSMSTR uses a proprietary high speed serial protocol to communicate,
via backplane connection, with up to 16 slave modules. Through the
same connection, the Master also provides power to the modules.
When powered up, the CSMSTR automatically identifies and
addresses connected slave modules. By storing the configuration
information of all of the modules, the CSMSTR is able to automatically
configure modules if they are replaced.
The Master provides high-speed RS232/422/485 communication
ports and an Ethernet port for connection to PCs, PLCs, and SCADA
systems. An extensive list of master and slave protocol drivers are
available to allow the CSMSTR to share and exchange variable data
with external devices. The 10 Base-T/100Base-TX Ethernet port can
also be used to connect and share data with other devices at high speeds.
The design of the Modular Controller Series high density packaging
and DIN rail mounting saves time and panel space. The controller
snaps easily onto standard top hat (T) profile DIN rail.
The CSMSTR is programmed with Crimson 2.0 software for
Windows® 2000 or later platforms. The software is an easy to use,
graphical interface which provides a means of communication
configuration, as well as commissioning and calibration of new systems.
SPECIFICATIONS
Power: 24 Vdc ± 10% 400 mA min. (1 module) 3.5A max. (16 modules + expansion Card) must use class 2 or SELV rated power supply.
Communications:
USB/PG Port: Adheres to USB specification 1.1. Device only using Type B connection
Serial Ports: Format and Baud Rates for each port are individually software programmable up to 115,200 baud.
RS232/PG Port: RS232 port via RJ12
COMMS Ports: RS422/485 port via RJ45, and RS232 port via RJ12
DH485 TXEN: Transmit enable; open collector, VOH = 15 VDC, VOL = 0.5 V @ 25 mA max.
Ethernet Port: 10 BASE-T / 100 BASE-TX RJ45 jack is wired as a NIC (Network Interface Card)
LEDs:
STS: Status LED indicates condition of master.
TX/RX: Transmit/Receive LEDs show serial activity.
Ethernet: Link and activity LEDs.
CF: Compactflash LED indicates card status and read/write activity
Memory:
On-Board User Memory: 4 Mbytes of non-volatile flash memory
On-Board SDRAM: 2 Mbytes
Memory Card: Compactflash type II slot for type I and type II cards (Used for optional database storage only)
Real Time Clock: Typical accuracy is less than one minute per month drift
Battery: Lithium coin cell (included). Typical lifetime of 10 years at 25 ºC (77°F)
Environmental Conditions:
Operating Temperature Range: 0 to 50°C (32 to 122°F)
Storage Temperature Range: -30 to +70°C (-22 to 158°C)
Operating and Storage Humidity: 80% max relative humidity, non-condensing, from 0 to 50°C (32 to 122°F)
Vibration According to IEC 68-2-6: 5 to 150 Hz, in X, Y, Z direction for 1.5 hours, 2 g's
Shock According to IEC 68-2-27: Operational 25g, 11ms in 3 directions.
Altitude: Up to 2000 meters
Construction: Case body is burgundy high impact plastic and stainless steel. Installation category I, pollution degree 2
Power Connection: Removable wire clamp screw terminal block
Wire Gage Capacity: 24 AWG to 12 AWG
Torque: 4.45 to 5.34 in/lb (0.5 to 0.6 N-m)
Mounting: Snaps onto standard DIN style top hat (T) profile mounting rails according to EN50022 -35 x 7.5 and -35 x 15
Certification and Compliances:
Safety:
UL Listed: File #E302106, UL508, CSA 22.2 No. 14-M05 LISTED by Und. Lab. Inc. to U.S. and Canadian safety standards IEC 61010-1, EN 61010-1:Safety requirements for electrical equipment for measurement, control, and laboratory use, Part 1
Electromagnetic Compatibility:
Emissions and Immunity to EN 61326: Electrical equipment for measurement, control and laboratory use
Immunity to Industrial Locations*:
Electrostatic discharge EN 61000-4-2, Criterion A 2, 4 kV contact discharge, 8 kV air discharge, Electromagnetic RF fields EN 61000-4-3, Criterion A 10 V/m, Fast transients (burst) EN 61000-4-4, Criterion A, 2 kV power, 2 kV signal, Surge EN 61000-4-5 Criterion A, 1kV L-L,2 kV L&N-E power, RF conducted interference EN 61000-4-6, Criterion A, 3 V/rms
Emissions: Emissions EN 55011 Class A
Weight: 456.4 g (15.1 oz)
|
 |
|
 |
† All dollar amounts on this site are shown in US currency.
Note: Controllers come with termination plug, terminal power block, and complete operator’s manual.
Ordering Example: (1) CSMSTRLE controller, (1) SFCRM2MC software, (1) G3CF512M G3CF512M, 512 MB flash 512 MB flash card, (1) CSDIO14R 8 inputs 6 relay output module, (1) PSDR0100 power supply = $1305
|
|
 |
|
 |
|  |
|
Keywords:Enhanced Modular Controller Series Master
|
Back to top |
|
|