Paddlewheel Flow Sensors |
| FP-5100 and FP-5300 |
|
 |
|
|
|
 |
Streamline your flow measurement operation with the FP-5100 Series flow sensor. Using this compact flow
sensor, a matched sensor installation fitting, an OMEGA® flow meter or controller, and ordinary
handtools, you can assemble a complete flow monitoring or controlling system in minutes. Accurate to
±0.2 fps, with repeatability at ±0.1 fps, this insertion sensor operates on a simple electromechanical
principle, proven in thousands of liquid flow applications worldwide. It all adds up to precision,
dependability, and convenience– basic advantages that are quickly surpassing its in-line competition.
Convert your maintenance hours into minutes with the FP-5300. Should a sensor, rotor, or O-ring need to
be replaced, it takes only seconds. Reduce your system downtime substantially with a stand-alone FP-5300
sensor, or simply add a Wet Tap Assembly and eliminate downtime completely. Combined with the FP-5300
during initial installation, the Wet Tap allows sensor removal without system shut-down. Optional local
or remote capability lets you place your meter up to 200 feet away without signal amplification, and you
can install the FP-5300 in pipe sizes ranging from 1/2 inch to 36 inches without a lot of additional
cost, because the price of the FP-5300 increases only slightly for larger pipe sizes.
Available in a choice of chemically resistant, non-contaminating housing materials, the FP-5300 stands
up to the harshest environments. The glass-filled polypropylene housing version is lightweight but
strong, which makes it ideal for handling a wide range of liquids, including corrosive fluids in
chemical processing. For processes involving acids and solvents, the PVDF (polyvinylidene fluoride)
housing version is a tough fluorocarbon that is highly resistant to more severe fluids.
The sensor works on a simple but precise electromechanical principle based on measuring the rate and
volume of flow in your pipe. Four permanent magnets, imbedded in the rotor blades, spin past a coil in
the sensor body. As the fluid flow causes the rotor to move, a sine wave signal is produced, directly
proportional to the flowrate. The patented “open cell” feature of the rotor ensures a linear, repeatable
output, up to 20 fps, with accuracy of ±0.2 fps. The result is minimal head loss and no cavitation.
Designed to allow optional conduit installation, the FP-5300 easily lets you comply with local codes
requiring conduit protection. For instance, pry off the plug on top of the sensor: underneath, you’ll
find a 1/2 FNPT thread. Using an optional conduit adaptor fitting kit, you can connect your conduit
FPM-5000-SCAK conduit adaptor kit), and an optional instrument back-cover kit will provide everything
you need for quick conduit connection to a meter or controller. Additionally, you can adapt to both
rigid and flexible liquid-tight conduits, protecting your system hookup from harsh elements and
mechanical damage.
Flow Range
Pipe
Size |
½" |
¾" |
1" |
1¼" |
1½" |
2" |
2½" |
3" |
4" |
5" |
6" |
8" |
10" |
12" |
Range
(gpm) |
1
to
19 |
1.7
to
34 |
2.7
to
54 |
4.7
to
94 |
6.4
to
127 |
10.6
to
210 |
15
to
300 |
24
to
461 |
40
to
794 |
63
to
1247 |
91
to
1801 |
156
to
3119 |
246
to
4915 |
349
to
6977 |
SPECIFICATIONS
Accuracy: ±1% full scale
Output Signal: 1 V p-p/fps
Output Frequency: 6 Hz/fps nominal
Flow Rate Range: 1 to 20 fps
Source Impedance: 8 kΩ
Maximum Pressure:
FP-5300 Series: 180 psig max @ 20°C (68°F)
FP-5100 Series: 200 psig max @ 20°C (68°F)
Minimum Temperature: 0°C (32°F)
Maximum Temperature: See chart on spec sheet for complete temperature and pressure rating
Pressure Drop: Equal to 2.5 m (8') of straight pipe
Material:
Transducer Housing: glass-filled polypropylene or PVDF
O-Rings: FKM
Shaft: Titanium or Hastelloy C(PVDF optional)
Rotor: PVDF
Maximum % Solids: 1% of fluid volume, non-abrasive, nonmagnetic, <100 micron diameter and length
Standard Cable Length: 7.5 m (25')
Max Viscosity: 1 centipoise (water); up to 5 cp above 5 fps velocity
|
| |
|
|
|
|
|
† All dollar amounts on this site are shown in US currency.
Note: Comes complete with operator's manual.
(OPTIONS SHOWN IN THIS "NOTE" ABOVE ARE PRICED IN US$)
Ordering Example: (1) FP-5300 Paddlewheel sensor for 1/2 to 4" pipes, $300.00, plus (1) DPF701 1/8 DIN Panel Meter for Flow Rate or Totalization, $280.00, $300.00 + 280.00 = $580.00
|
|
|
|
|
| |
|
|
|
|
|
 |
 |
 |
|
|
Related Links -
Manual, Related Products
|
|
|
|
|
|
 |
|
|
|
Product Manual
|
|
Download
FP-5100,FP-5300,FP-5600,FP-8500 - Paddlewheel Flow Sensors
|
|
Download
FP-5100,FP-5300,FP-5600,FP-8500 - Paddlewheel Flow Sensors
|
|
Related Products
|
|
|
|
 |
FP90 Series:
|
|
Flow Transmitter with rate/total display - relay outputs available
|
|
|
|
|
 |
FP-319:
|
|
The Downtime Eliminator: Wet Tap Valve Assemblies
|
|
|
|
 |
FPM-5750:
|
|
Battery Powered Flow Indicator and Totalizer
|
|
|
|
|
 |
FPM-5500:
|
|
Flow Indicators and Totalizers With Analog & Digital Displays
|
|
|
|
|
|
|
 |
|
|
