Call us at 1-888-826-6342
Load Washers to Measure Bolt Compression
Bolt Sensors with Mounting Washers
Volume discounts available
Volume Discount Schedule
| Quantity | Price each |
|---|---|
| 1-9 | $526.52 |
| 10-24 | $500.19 |
| 25-49 | $489.66 |
| 50-99 | $468.60 |
| 100+ | $458.07 |
Added to Your Shopping Cart
Configuration complete.
Please add to cart to keep it or exit the configuration
Please add to cart to keep it or exit the configuration
Failed to Save Configurations, Click on Configure Button Start Again
LC901-3/8-10K Model Options
View all modelsEdit these specs to order a different model. Not all combinations are valid. Options compatible with previous selections will be in bold.
*Highlighted options are not compatible. Please select a different combination.
Weight Capacity
Measurement Units
OD
Through hole (ID)/ Threaded hole dimension
Height
Connection Type
Cable Length
Force Direction
Linearity
Electrical Output (Nominal)
- Safe Overload 130% of capacity
- Ultimate Overload 150% of capacity
- Zero Balance ±4% FSO
- Accuracy ±3.5% FSO (linearity, hysteresis and repeatability combined)
- Compensated Temp Range 16 to 71°C (60 to 160°F)
- Construction Stainless steel
- Excitation 5 Vdc (10V max)
- Operating Temp Range -54 to 93°C (-65 to 200°F)
- Output 2 mV/V nominal
- Thermal Effects Zero: ±0.018% FSO/°C Span: ±0.036% rdg/°C
- Bridge Resistance 120 Ω nominal
- Electrical Connection 1.2 m (4') insulated shielded cable
OMEGA’s LC900 Series bolt force sensor is a compression load cell designed to measure the clamping force of a bolt. With excellent long term stability and all stainless steel construction, the LC900 Series delivers high reliability in severe industrial environments. This unit is designed to operate by mounting on a flat surface between two mounting washers (included).
The LC901 is also available in metric configurations, with ranges from 0-10,000 to 0-500,000 N. Please see the LCM901 for complete details, or contact our Pressure department for more information.
SPECIFICATIONS
Excitation: 5 Vdc (10V max)
Output: 2 mV/V nominal
Accuracy: ±3.5% FSO (linearity, hysteresis and repeatability combined)
Zero Balance: ±4% FSO
Operating Temp Range: -54 to 93°C (-65 to 200°F)
Compensated Temp Range: 16 to 71°C (60 to 160°F)
Thermal Effects:
Zero: ±0.018% FSO/°C
Span: ±0.036% rdg/°C
Safe Overload: 130% of capacity
Ultimate Overload: 150% of capacity
Bridge Resistance: 120 ? nominal
Construction: Stainless steel
Electrical Connection: 1.2 m (4') insulated shielded cable
The LC901 is also available in metric configurations, with ranges from 0-10,000 to 0-500,000 N. Please see the LCM901 for complete details, or contact our Pressure department for more information.
SPECIFICATIONS
Excitation: 5 Vdc (10V max)
Output: 2 mV/V nominal
Accuracy: ±3.5% FSO (linearity, hysteresis and repeatability combined)
Zero Balance: ±4% FSO
Operating Temp Range: -54 to 93°C (-65 to 200°F)
Compensated Temp Range: 16 to 71°C (60 to 160°F)
Thermal Effects:
Zero: ±0.018% FSO/°C
Span: ±0.036% rdg/°C
Safe Overload: 130% of capacity
Ultimate Overload: 150% of capacity
Bridge Resistance: 120 ? nominal
Construction: Stainless steel
Electrical Connection: 1.2 m (4') insulated shielded cable
Rated 3 out of
5
by
Anonymous from
120 Ohm Load Cells
The load cells have 120 Ohm resistance. Many of the load cell amplifiers available, including the one recommended for this product, require the load cell to have at least 300 Ohms resistance. That makes this device hard to use.
Date published: 2020-10-26
What is the outside diameter of the signal cable and what is the wire gauge of its conductors?
dmeigs LC901 wire gauge is 24 AWG, for further questions kindly email pressure@omega.com
Thank you
Date published: 2020-07-03
What is the actual transducer height without the additional washers?
MLFEP, Thank you for your question. Please open the spec sheet and review the "W" dimension corresponding to your range.
Date published: 2020-07-01
Are the top and bottom washers required if the bottom of the transducer sits on a flat surface, and the item on the top has a .750 O.D. and .266 I.D.?
The top washer should always be used. It assures the load is distributed around the I.D. evenly. The bottom washer would not be need if the surface the surface the load is resting on is perfectly flat
Date published: 2021-11-08
