The OMEGA™ DP41 Series of digital panel meter/controllers has set the world standard for accuracy and quality in industrial instrumentation. These meters can measure a broad spectrum of DC voltage and current ranges such as 0-100 mV, 0 to 5 Vdc, 0 to 10 Vdc, 4 to 20 mA, 0 to 20 mA and more as well as inputs from 9 thermocouple types and from most RTDs, pressure transducers, load cells, strain gages, and potentiometers. Models include the DP41-U, which covers all the input types.
Standard features include 6-digit display; 5 front-panel pushbutton keys; 4 open-collector outputs; and alarm/control, and analog outputs. Configurable analog output ranges are 0 to 20 mA, 4 to 20 mA, 0 to 5 Vdc, and 0 to 10 Vdc.
On-board excitation allows these meters to power virtually any sensor or transmitter, and 4 setpoints give the user numerous control/alarm possibilities. Setpoint configurations include active above or below; latching or non-latching; and high deviation, low deviation, or band deviation.
With the RS232/485 serial communications option, the user can set the display parameters and read the current, max, and min values remotely. The DP40-R4 board option provides four relays, activated by the selected setpoint.
SPECIFICATIONS Accuracy: ±0.005% of range +/- 5 counts Span Temperature Coefficient: ±20 ppm Step Response: 1s to 99.9% Warm-Up to Rated Accuracy: 50 min Operating Environment: 0 to 50°C (32 to 122°F); 95% RH,non-condensing Storage Temperature: -40 to 85°C (-40 to 185°F) Power: 115 or 230 Vac, 49 to 400 Hz; 10 to 32 Vdc Power Consumption: 6 W nom., 10 W max Normal-Mode Rejection: 60 dB Common-Mode Rejection: 120 dB Common-Mode Voltage: 1500 Vp per HV test Resolution: 17-bit Conversion: Dual-slope technique Reading Rate: 3/s or 13/s, 60 Hz; 3/s or 12/s, 50 Hz Display: Red or green 6-digit, 14-segment, 13.7 mm (0.54") high; 4 alarm indicators Dimensions: 48 H x 96 W x 165 mm D (1.89 x 3.78 x 6.5") Panel Cutout: 45 H x 92 mm W (1.772 x 3.622"); 1?8 DIN Weight: 574 g (1.27 lb) Setpoint Outputs: 4 isolated open collector; rated 150 mA at 1V sink, 30V open 4-Relay Option: Dual 5 A relays and dual 3 A relays 0 to 10V/0 to 20 mA/4 to 20 mA, user selectable; 354 Vp isolation; 15-bit resolution; 0.1% accuracy; 50 ms step response RS232 Communications: 300/600/1200/2400/4800/9600/19.2K baud; RJ11 4-wire connection; programmable to transmit current display, alarm status, min/max, actual measured input value and status RS485 Communications: 300/600/1200/2400/4800/9600/19.2K baud; RJ12 6-wire connection; addressable from 0 to 199 Voltage Input Ranges: 0 to 100 mV, 0 to 1V, 0 to 5V, 1 to 5V, 0 to 10V, 0 to 100V, ±50 mV, ±500 mV, ±5V, ±50V Current Input Ranges: 0 to 20 mA, 4 to 20 mA Input Configuration: Single-ended Polarity: Unipolar/bipolar, programmable Span Adjustment: 0.00001 to 500,000, programmable Offset Adjustment: 0 to 999,999 or 0 to -99,999, programmable Thermocouple Input Types: J, K, T, E, R, S, B, N, J DIN RTD Input: Any 6? to 6 k? NIST or DIN platinum and any linear RTD RTD Connection: 2-, 3- or 4-wire Sensor Break Protection: Up-scale or down-scale, programmable Sensor Excitation: 10V at 30 mA; 24V at 25 mA
If the use of PM in your question refers to Phase Modulation the answer would be no. The DP41-S is simply a 115VAC powered scalable digital display. It accepts DC signals to the millivolt, Voltage or milliamp range.
Answered by: jkengineer
Date published: 2019-08-05
Beside two pages PDF manual. Do you have full IO&M manual for the meter DP41-S-AR4. if yes, can you send to me?
RS-232/RS-485 Communications board with DP40-S24 option comes with 6.5' communications cable with phone plug termination. For proper termination to a computer, 9-pin and 25-pin connec tors are offered on this page.