text.skipToContent text.skipToNavigation

If you have previously used the Omega Website, you will need to Reset your Password on the new site.
Resetting your password is required one time only.

Configure Product
Saved Configuration
View Configuration
Terms and Conditions
Saved Addresses
Your card information was not accepted. Please contact the issuing bank for details.
Payment submission timed out. The server might be busy.
There was an error processing your request.
Please verify there are no missing or invalid fields.
Please enter a card number
Please select a card type
Please enter a value for this field
Please enter an expiry month
Please enter an expiry year
Please enter an issue number
Please enter a start month
Please enter a start year
The card number is not valid
The card type is not supported
The card verification code is not valid
The expiry month is not valid
The expiry year is not valid
The issue number is not valid
The start month is not valid
The start year is not valid
This field is required
Errors were found with the address you provided. Please verify your address.
Date should be in MM/DD/YYYY format
Please enter valid values
Please enter future date
Please enter the shipping date
Shipment date is updated

Industrial Cleaning/Fluidized Baths

Item# FFB51

Industrial Cleaning/Fluidized Baths Industrial Cleaning/Fluidized Baths
FFB51 and FFB52 industrialfluidized baths are our mostpopular units due to theireconomical price and smallersize. They offer a front panelmounted rotameter for adjustmentof the fluidizing air flow andare ready for use out of thebox with the included chargeof aluminum oxide.For years, plastic manufacturershave come to depend on industrialfluidized baths (FFB series) forsafe, efficient and cost effectivecleaning of tooling, components,systems and parts (i.e. dies,breaker plates, nozzles, tools,tips, spinnerets, extruder screws,manifolds, etc.) The FFB Serieswill remove almost all polymers,including plastic, paint, epoxy,rubber and adhesives, as well asother hydrocarbon-based productssuch as oils, fluids, grease,lubricants and coatings.Parts immersed into the FFBseries are cleaned by the hightemperature (up to 600°C)environment within a bath mediaof fluidized aluminum oxide thatinstantly starts to degrade plasticto carbon, which then leaves thebath as CO2. This instant heatingand minimized quenching givesshorter cleaning times than withconventional ovens, and with theeven and consistent heat of thebath, results in greatly reducedmetal fatigue and tool damage.Omega baths can be fluidizedwith either compressed house airor an inert gas such as nitrogenor argon. It should be noted thatfluidized baths and the actioncreated in the aluminum oxide arenot abrasive to items immersedfor normal cleaning or heat treatmenttimes. Typical cleaning timesrange from 30 minutes to 2 hoursdepending on bath loading,temperature and amount ofmaterial to be cleaned.The excellent thermalperformances the FFB seriesmake them a good choicefor basic heat treatment, testand calibration as well asreactive analysis.
FFB51
  • Clean Extrusion and Injection Molding Tooling
  • Fast Cleaning: • Minimizes Costly Production Equipment Down-Time • Reduces Any Impact on Hardness of Material Cleans in One-Third the Time of Ovens
  • No Tool Damage as Compared to Using Ovens, Torches, Wire Brushes, and Scraping
  • Unattended Cleaning Reduces Labor Costs vs. Using Manual Cleaning Methods
  • Typical ROI in 6 to 9 Months
  • Not Abrasive to the Tooling
  • Easily Burns Off Material in the Small Holes of Breaker Plates, Dies, Nozzles and Other Tooling
  • Well Insulated, Built-to-Last and Energy Efficient (25 kWH Typical FFB52 Run)
  • No Need for Consumables, Solvents or Any Other Chemicals
  • Removes Most All Polymers from Tooling
Maximum Temperature Measurement
Supply Voltage
Power Source
Accuracy Value
Measurement Type
Batteries Included
See All Options
Quantity Price each
1-9 $7,461.00
10-24 $7,087.95
25-49 $6,938.73
50-99 $6,640.29
100-199 $6,491.07
200+ $6,341.85

In stock

Lead Time ( If not in Stock): 6 weeks

Product Specs

FFB51 and FFB52 industrialfluidized baths are our mostpopular units due to theireconomical price and smallersize. They offer a front panelmounted rotameter for adjustmentof the fluidizing air flow andare ready for use out of thebox with the included chargeof aluminum oxide.For years, plastic manufacturershave come to depend on industrialfluidized baths (FFB series) forsafe, efficient and cost effectivecleaning of tooling, components,systems and parts (i.e. dies,breaker plates, nozzles, tools,tips, spinnerets, extruder screws,manifolds, etc.) The FFB Serieswill remove almost all polymers,including plastic, paint, epoxy,rubber and adhesives, as well asother hydrocarbon-based productssuch as oils, fluids, grease,lubricants and coatings.Parts immersed into the FFBseries are cleaned by the hightemperature (up to 600°C)environment within a bath mediaof fluidized aluminum oxide thatinstantly starts to degrade plasticto carbon, which then leaves thebath as CO2. This instant heatingand minimized quenching givesshorter cleaning times than withconventional ovens, and with theeven and consistent heat of thebath, results in greatly reducedmetal fatigue and tool damage.Omega baths can be fluidizedwith either compressed house airor an inert gas such as nitrogenor argon. It should be noted thatfluidized baths and the actioncreated in the aluminum oxide arenot abrasive to items immersedfor normal cleaning or heat treatmenttimes. Typical cleaning timesrange from 30 minutes to 2 hoursdepending on bath loading,temperature and amount ofmaterial to be cleaned.The excellent thermalperformances the FFB seriesmake them a good choicefor basic heat treatment, testand calibration as well asreactive analysis.

  • CE Icon CE

en-US
en
Save Configuration