Rugged In-Line Flow Sensors
Available in 1/2", 3/4", and 1-1/4" sizes with anodized aluminum, brass and/or stainless
steel flow cartridges. Comes with 4.5 m (15') of stripped end integral cable. In the field,
integral cable can be extended up to 300 m (1000') with shielded copper cable. Units are
securely protected in a sturdy cast aluminum enclosure, and are easy to install and mount
in any position, vertical or horizontal. Capable of monitoring fluids to 150 GPM or
pneumatic lines to 1000 SCFM.
SPECIFICATIONS Temperature Range: -29 to 116°C (-20 to 240°F) Maximum Pressure: 3500 psig (liquids); 1000 psig (gases) Power Requirement: 0 to 5 Vdc Output: 10 to 30 Vdc @ 0.75W max 0 to 10 Vdc Output: 12 to 30 Vdc @ 0.75W max 4 to 20 mA Output: Loop-powered, 30 Vdc max Power Consumption: 25 mA max Circuit Protection: Reverse polarity and current limit Repeatability: ±0.5% Non-linearity: ±0.05% Isolation: Inherently isolated from the piping system Display: Fixed or toggle modes of operation for rate and totalizer display. 8-digit, 0.70" high numeric display for rate and total 8-digit 0.35" high alphanumeric display for units and setup. Response Time: 1.0 sec Temperature Drift: 0.05% of span per °C max Analog Outputs: 4 to 20 mA into 1kΩ max 0 to 5 Vdc into 10 kΩ min 0 to 10 Vdc into 10 kΩ min User Connections: 15-foot pig-tail (standard) Transmission Distance: 4 to 20 mA limited by cable resistance 0 to 5 Vdc 300 m (1000') maximum 0 to 10 Vdc 300 m (1000') maximum ENCLOSURE Material: Anodized and epoxy powder-coated aluminum with polycarbonate lens Seals: Silicone gasket between enclosure and lens/cover. FKM O-rings between enclosure and flow meter body. Connection: 4-pin connection (standard) Fasteners: T303 SS Rating: NEMA 12 & 13 (IP52/54) Materials: 2024 - T351 anodized aluminum body, piston and cone C360 Brass body, piston and cone PETROLEUM (OIL) COMMON PARTS Spider Plate: T316 SS Spring: T302 SS Fasteners: T303 SS Pressure Seals: FKM Lens: Polycarbonate Retaining Ring: SAE 1070/1090 carbon steel Retaining Spring: SAE 1070/1090 carbon steel Internal Magnet: PPS/ceramic Enclosure Seal: Silicone gasket WATER-BASES, WATER, AIR COMMON PARTS Spider Plate: T316 SS Spring: T302 SS Fasteners: T303 SS Pressure Seals: FKM Lens: Polycarbonate Retaining Ring: T316 SS Retaining Spring: ST316 SS Internal Magnet: PPS/ceramic Enclosure Seal: Silicone gasket
† All amounts shown in USD Note: Comes complete with 4-pin connector, 15 feet of cable, and operator’s manual.
Ordering Example: (1) FLR6105D Flow transmitter, 0.5 - 5.0 GPM for oil, with analog output, $785.00
Rated 2 out of
Accurate but flawed designInitial testing revealed accurate totalized flow but having to pull off the cover (4 screws) every time you want to reset the totalizer is ridiculous. Considering using the 2 unused wires and a couple of PLC outputs to mimic button pressing. So much for the warranty. Can't output the totalized flow number instead of the flowrate.