Omega’s new DPF20 Series of indicators offer real flexibility for measurement of a wide range of frequency or pulse inputs. The display is easily configured to indicate frequency, rate, period or count. This makes the meter ideal for flow applications where they can display flow rate or total from a variety of different flow sensors. Or for quadrature signals, to indicate angular position or rotational speed and direction.
The DPF20 series offers exceptional performance at an economical price, with some unique and powerful features.
Multiply, divide and preset values
configure a second setpoint in the same alarm, to create “alarm windows”
configure independent activation and deactivation delays
configure alarm to activate as high or low
failsafe function – normally closed relay requires activation for non-alarm condition
latched alarms function – operator reset required
Counter Reset, Stop or Continue
Power up delay
Allows for a delay in the start-up timeafter powering the instrument. During this time the instrument performs no measurement or control. Ability to reset the display count on instrument start-up.
Select from 5 levels of LED intensity.
Password protect the configuration menu. This blocks access to the instrument set-up parameters, but the operator can still access set-point values.
Max / min memory
Front panel key selection of display minimum or maximum values
The fast and simple way to configure a sensor. Select from a predefined list Eg. NPN, PNP, Namur, pick-up, inductive, etc. The instrument will automatically configure the required parameters for the selected sensor (pull-up / pull-down resistors, trigger level, excitation voltage, etc)
Simple selection of the optimal trigger level for the sensor input. The display indicates up or down reflecting the status of the input signal level. When the LED changes state continuously the optimal trigger level has been achieved.
Specifications Main Functions: Counter, ratemeter, period meter Display Digits: 6 Display Range: 999999/-199999 Decimal Point: Configurable LED Color: Red standard; green optional Digit Height: 14 mm (0.55") Signals Accepted: NPN, PNP, Namur, pick-up, TTL, inductive, mechanical, quadrature Excitation Voltage: 5 Vdc, 9 Vdc, 15 Vdc, 18 Vdc (max. 70 mA) Maximum Vdc at Input Terminals: ±30 Vdc Input Impedance: 2.4 kO with pull-up or pull-down resistor; 470 k without resistor Quartz Accuracy: ±0.01% Thermal Stability: 20 ppm/ºC Display Refresh: 15/second Maximum Frequencies: Counter: Up to 250 KHz Ratemeter and Period Meter: Up to 500 KHz Minimum Frequencies: Down to 1 mHz (0.001 Hz) (ratemeter and period meter) Standard Power: 85 to 265 Vac/DC (isolated 2,500 Vac) Low Power: 11 to 60 Vdc and 24/48 Vac (isolated 1500 Vac) Power Consumption: <1.5 W (meter only); < 4.0 W (meter with options) Connections: Plug-in screw terminal Slow Function: For low frequency rate meter applications Fast Function: For high frequency counter applications Scaling Factor: Multiplier and divider from 1 to 999999 Configurable Reset: Front panel and rear remote reset, and reset linked to alarm activation Preset: Configurable Retention Memory: Recovers count value in case of power loss Dimensions and Environment Weight: <150 grams (<5.3 oz) Front Panel Size: 96 x 48 mm (3.78 x 1.89") Panel Cut-Out: 92 x 44 mm (3.62 x 1.73") Depth Behind Panel: 91 mm (3.58") including terminals Operating Temperature: 0 to 50ºC (32 to 122ºF) Storage Temperature: -20 to 70ºC (-4 to 158ºF) Warm Up: 15 minutes Front Panel Protection: NEMA 4 (IP65)
I would like to know if the DPF20 is compatible with FTB4707 Water Flow Sensor... to measurement the GPM.
Asked by: Irving
Yes. The DPF20 is compatible with FTB4707 water flow sensor to measure flow rate (GPM) or total gallons.
Answered by: SAE HPO
Date published: 2020-01-24
Could a DPF20-HV-AO display be setup with an FTB-1400 series flow meter to measure flow rates? The flow meter has a magnetic pickup sensor producing a 30 mV/P-P signal.
Asked by: AdamB_666
Yes. The FTB-1400 series is compatible with rate/totalizer display DFP20-HV-AO
Answered by: ASE HPO
Date published: 2019-10-25
I have a DPF20-LV, I was testing the functions and added a password. Now 3 months later I do not recall what that password was, How to I break the pass to get into the unit to see the setting and scaling I used or worst case how do i reset the whole unit.
Asked by: RickL
Master password is 000007
Answered by: SAE HPO
Date published: 2019-08-06
I am looking to verify that a panel meter such as the Item# DPF20-HV-R1-AO could be used to read/calibrate the output of a rotary encoder such as an AU-ZBG model.
Asked by: InduMar
Thank you for contacting Omega Engineering. Concerning your inquiry, yes the DPF20-HV-R1-AO is compatible with rotary encoders such as an AU-ZBG. It will convert the pulses from the encoder to a speed value, that will be displayed on the screen.