Call us at 1-888-826-6342
Compact RTD Probe with Mounting Thread and M12 Connector
Compact RTD Temperature Sensors
Volume discounts available
Volume Discount Schedule
| Quantity | Price each |
|---|---|
| 1-9 | $50.25 |
| 10-24 | $47.74 |
| 25-49 | $46.73 |
| 50-99 | $44.72 |
| 100-199 | $43.72 |
| 200+ | $42.71 |
Added to Your Shopping Cart
Configuration complete.
Please add to cart to keep it or exit the configuration
Please add to cart to keep it or exit the configuration
Failed to Save Configurations, Click on Configure Button Start Again
- Extremely Rugged
- Molded (IP67) 4-Pin Connector with M12 Male Thread
- Fast Response Time*
- -50 to 120°C (-58 to 248°F)
RTDM12-1/8NPT-3MM-24MM-A Model Options
View all modelsEdit these specs to order a different model. Not all combinations are valid. Options compatible with previous selections will be in bold.
*Highlighted options are not compatible. Please select a different combination.
Process Connection Size
Accuracy
Nominal Output
Probe Length
Category
Process Temperature Unit
Process Temperature Min
Process Temperature Max
Process Temperature Range
Sensor Application
Number of Wires
Sheath Material
Probe Diameter
Termination Connection Type
This RTD plug sensor is ideal for pressure vessel applications, pressurized containers and applications requiring a temperature sensor with an NPT mounting fitting. The single element design has a 1/8' diameter, 316 stainless steel probe that extends 13 mm (0.51') or 24 mm (0.94') from a 1/8 NPT mounting thread. The M12 connector assures a very reliable connection. Extension cables are offered in different lengths with right or straight angles.
Specifications
Sensing Element: RTD PT100Ω @ at 0°C to IEC 751 class A
Construction: Screw in RTD probe for direct immersion, one piece construction
Case Material: AISI 316SS
Temperature Range: -50 to 120°C (-58 to 248°F)
Maximum Pressure: 40 bar (580 psi)
Process Connection: 1/8 NPT
Connection: 4-pin male connector with body in molded Nylon and M12X1 metal thread (to DIN-VDE 0627) with degree of protection IP67 (TMax 90°C)
Insulation Resistance: 100 MΩ with 100 Vdc
Response Time*: Less than 5 seconds
Marking: Each probe is permanently marked with the exact ohmical calibration test value at 0°C, the manufacturing date and a traceability code
Specifications
Sensing Element: RTD PT100Ω @ at 0°C to IEC 751 class A
Construction: Screw in RTD probe for direct immersion, one piece construction
Case Material: AISI 316SS
Temperature Range: -50 to 120°C (-58 to 248°F)
Maximum Pressure: 40 bar (580 psi)
Process Connection: 1/8 NPT
Connection: 4-pin male connector with body in molded Nylon and M12X1 metal thread (to DIN-VDE 0627) with degree of protection IP67 (TMax 90°C)
Insulation Resistance: 100 MΩ with 100 Vdc
Response Time*: Less than 5 seconds
Marking: Each probe is permanently marked with the exact ohmical calibration test value at 0°C, the manufacturing date and a traceability code
Rated 5 out of
5
by
dbech1 from
Good Sensor
Easy to find and at a good price. Online catalog was easy to navigate.
Date published: 2018-02-13
What is the temp coefficient for this? Is it the standard 0.00385 ohm/ohm/C?
Thank you for your inquiry. Yes, it is the European curve 0.00385.
Date published: 2023-08-17
Where is the wiring diagram/schematics for RTDM12-1/8NPT-3MM-24MM-A?
Thank you for your inquiry. Please see wiring diagram on the Data Sheet (PDF).
Date published: 2023-02-28
What is the maximum recommended cable length for these RTDs?
Thank you for your inquiry John. You can use the 3 m long M12CFM-P24STPC-SFSR-FL-3 cable or the 20 m long M12CFM-T24SSPC-SFSR-FL-20 cable with this probe without any issues. Anything longer than these cables, the wire gauge and the wire length would introduce error into the measurement.
Date published: 2022-06-26
Can this temperature used to measure the hot air temperature flowing in a duct or pipe?
Yes, the RTDM12-1/8NPT-3MM-13MM-A can be threaded into a pipe or duct to measure hot air flow.
Date published: 2019-10-15
Is the Compact RTD compatible with the CND3 Temperature and Process PID Controller?
Yes, the CND3 controller will take the input signal from this sensor.
Date published: 2020-03-13