Hermetically Sealed Thermistor Sensors
Hermetically Sealed Flexible Thermistor Sensors, PFA Jacketed
Added to Your Shopping Cart
Configuration complete.
Please add to cart to keep it or exit the configuration
Please add to cart to keep it or exit the configuration
Failed to Save Configurations, Click on Configure Button Start Again
- Available in 3 Standard Resistance Values: 2252 Ohms, 5000 Ohms or 10,000 Ohms at 25°C.
- Interchangeability: ±0.1°C Between 0 and 70°C.
- Temperature Range -80 to 150°C (-110 to 302°F)
- Available in Standard Lengths of 40, 80 and 120 Inches (1, 2 and 3 Meters).
- PFA Jacketed Design is Highly Resistant to Chemicals and Oils
- Easily Sterilized for Food Applications
- Response Time = 3.75 Seconds Max in Water Flowing at 3 Feet per Second (63%)
HSTH-44033-1M Model Options
View all modelsEdit these specs to order a different model. Not all combinations are valid. Options compatible with previous selections will be in bold.
*Highlighted options are not compatible. Please select a different combination.
Nominal Resistance
Cable Length
Termination Connection Type
Additional Feature
Category
Sensor Type
The HSTH Series Flexible Thermistor Sensors are hermetically sealed at the sensor tip to provide continuous protection from corrosive environments. This unique Thermistor temperature probe design provides a small, flexible, and electrically isolated Thermistor element, suited to a variety of applications. The HSTH Series is available in three resistance values: 2252Ω, 5000Ω and 10000Ω.
If you need higher operating temperatures, see our RTD Version or Thermocouple Version which may be a better fit for your application.
If you need higher operating temperatures, see our RTD Version or Thermocouple Version which may be a better fit for your application.
Rated 1 out of
5
by
Joe p from
Very disappointing!
Quality control and customer service needs improvement! I ordered 6 and only got 3 that worked. I sent the 3 bad ones back, and after months of waiting for the sensors that I needed months ago, I finally received 2 good ones and 1 bad one. I will not be using Omega again. Very disappointing!!!
Date published: 2020-05-26
Rated 4 out of
5
by
Anonymous from
Precise Temperature Control
Fairly accurate, but tip is delicate and you cannot bend it too much otherwise the internal thermistor breaks.
Date published: 2020-09-29
Rated 1 out of
5
by
Joe p from
Need to improve quality control
This sensor is great when you get one that works. I ordered 6 and 3 didn't work. No prob I contacted Omega and they said send it back and we will send you new ones. After months of waiting they sent me 3 replacement sensors. Only two of those 3 sensors actually worked. I will not be using Omega for my futher needs.
Date published: 2020-05-26
Rated 5 out of
5
by
Loureiro58 from
Great product
Your tech suport is very helpful!
Thank you very much !
Date published: 2017-12-31
Is this a NTC(negative temperature coefficient) thermistor?
Thank you for your email . The HSTH-44031-120 uses a NTC thermistor which
drops in resistance with increase temperature . The Thermistor Resistance vs. Temperature table is found per the attached link
https://www.omega.co.uk/temperature/Z/pdf/z256-257.pdf
Date published: 2020-03-23
what is the diameter of the Item# HSTH-44031-120 probe end? thanks
Product appearance and tip diameter information is available on the Data Sheet (PDF) link on this page. Tip size ranges from 2.3 to 2.5 mm (0.090 to 0.100")
Date published: 2020-04-03
