Call us at 1-888-826-6342
High Temp Relative Humidity Temperature Transmitter w/ Probe
High Temperature Relative Humidity/Temperature Transmitter, with Remote Probe
Added to Your Shopping Cart
Configuration complete.
Please add to cart to keep it or exit the configuration
Please add to cart to keep it or exit the configuration
Failed to Save Configurations, Click on Configure Button Start Again
- Remote Stainless Steel Probe (included)
- 64 mm (2.5") Long Wall Mounted Probe
- 216 mm (8.5") Long Duct Mounted Probe
- 2% RH, 0.5°C Accuracy
HX15-D Model Options
View all modelsEdit these specs to order a different model. Not all combinations are valid. Options compatible with previous selections will be in bold.
*Highlighted options are not compatible. Please select a different combination.
Additional Feature
Input Type
Input Ranges
Output Type
Supply Voltage Type
Programability
Description
The HX15 series two wire remote transmitters measure relative humidity and temperature over a large temperature range (-40 to 180°C). The HX15-W 64 mm (2.5") stainless steel probe is used for wall mounting. The HX15-D 216 mm (8.5") stainless steel duct probe has a removable flange. The probes are connected to housings with 1 m (40") PFA cables. Probes are not field replaceable.
Rated 5 out of
5
by
Kevin217 from
Good product
High quality. Easy to set up and calibrate. Last a lot longer than a year. I just changed one that was 4 years old. That's a long time for an accurate humidity probe.
Date published: 2017-03-14
Rated 5 out of
5
by
John Dudasik from
Quality and Accuracy for a high temp environment
We needed a temp humidity sensor that could withstand a 210deg airstream. The sensor we purchased from Omega was just what we were looking for! Quality, accuracy, and ease of use were obvious from the start!
Date published: 2022-09-23
So what type of a readout does this interface with/ I just see a probe and a box? what else do I have to buy to actually read the RH%?
Thank you for your inquiry. The output of this unit is in mA. Therefore, any unit like a meter that takes a mA output would suffice to record a measurement. Please review the following link: https://www.omega.com/en-us/control-monitoring/meters/c/universal-input-meters
Date published: 2022-11-21
Do the probe cable can withstand up to 180 Degree Celcius?
Hi Jag Oh
Thank you for the inquiry. Yes, probe and cable are rated for 180 C. Please review manual for max RH values at the elevated temperatures.
Best regards
OMEGA
Date published: 2021-06-15
Can duct flange probe be provided with 10 meter probe to the box ?
Hi Amit,
Thank you for the inquiry. We are unable to offer extended sensor cable for the HX15 series unfortunately.
Best regards
OMEGA
Date published: 2023-11-28
What is the function of the RH Offset trimpot? If it is inadvertently adjusted, is there a way to reset it?
The "RH Offset" potentiometer is for 'factory' use only and should not be turned. If it is turned during the calibration process (or at any time) the unit should come back for factory calibration, as our factory has a specific procedure to get the unit back into specs using this pot along with the other ones. The field calibration procedure does not incorporate this potentiometer.
Date published: 2020-09-19
Can the electronic board be removed from the enclosure? Do you have an accurate drawing of the board so I can mount it inside my own enclosure?
Hi Vederstein
Thank you for the inquiry. I would not recommend removal of the electronics board as it provides mechanical protection of components as well as support for the board itself. The board and the sensor are calibrated as a system.
We do not have drawings available for the board and components.
Best regards
OMEGA
Date published: 2020-08-21
Accessories