LVDT Linear Position Sensors with DC Output
0 to 150 mm, 0 to 10 Vdc Output
Volume discounts available
Volume Discount Schedule
Quantity | Price each |
---|---|
1-4 | $1,285.00 |
5-9 | $1,220.75 |
10-24 | $1,195.05 |
25-49 | $1,143.65 |
50-99 | $1,117.95 |
100+ | $1,092.25 |
Added to Your Shopping Cart
Configuration complete.
Please add to cart to keep it or exit the configuration
Please add to cart to keep it or exit the configuration
Failed to Save Configurations, Click on Configure Button Start Again
- Being replaced by the new LD600A series
- Better Than 0.2% Linearity
- 5 to 150 mm Total Travel Lengths Available
- Rugged 19 mm Dia. Stainless Steel Body
- Rigid Stainless Steel Carriers
- IP67 Environmental Rating
- Guided Core with Removable Spring for Easy Installation
- Large Bore to Core Clearance
- Applications:
 Proprotional Actuators
 Robotic Automation
 Linear Servo Actuator
 Industrial Automation Controls
 Motion Control
LD621-150 Model Options
View all modelsEdit these specs to order a different model. Not all combinations are valid. Options compatible with previous selections will be in bold.
*Highlighted options are not compatible. Please select a different combination.
Range
Electrical Output
Housing Length
Linearity
Rating
Housing Diameter/Width
Features
- Body Diameter 19 mm
- Body Material 300 SS
- case Material 300 SS
- Environmental Rating/Protection IP67
- Maximum Ambient Temperature 85 {C} (185 {C})
- Measurement Type Displacement
- Output Signal Type DC
- Travel Range 5 to 150 mm Total Travel Lengths Available
The LD620 series has been replaced by the new and improved LD600A series. Many ranges are in stock, available for immediate shipment. Link "LD600A Series" in redirected to the LD600A page LD621A-100
The LD620 DC output displacement tranducers have improved IP67- rated sealing, coupled with new polymer guides with rigid carriers. These transducers are accurate and reliable, especially in wet and corrosive conditions. Output options are either ±5 Vdc (LD620) or 0-10 Vdc (LD621). An unusually large bore-to-core clearance is maintained throughout the range. This makes installation easier and helps prevent misalignment on automation actuators and other industrial automation controls.
SPECIFICATIONS
Linearity: <0.2% FSO
Excitation Voltage: 10 to 30 Vdc @ 25 mA maximum
Output Ripple: 0.02% FSO
Bandwidth: 500 Hz (-3 dB)
Storage Temp: -20 to 85°C (-4 to 185°F)
Operating Temp: 0 to 65°C (32 to 149°F)
Sealing: IP67
Vibration (Sinusoidal Frequency):
10 to 50 Hz: 1 to 10 g rms linear Amplitude
50 Hz to 1 kHz: 10 g rms Amplitude
Shock:
Drop Testing: 1 m (3') onto hard surface
Topple Testing: 10 times each end onto hard surface
Case Material: 300 SS
Cable: PFA, 2 m (6') long
Core Material: Nickel-iron
SPECIFICATIONS
Linearity: <0.2% FSO
Excitation Voltage: 10 to 30 Vdc @ 25 mA maximum
Output Ripple: 0.02% FSO
Bandwidth: 500 Hz (-3 dB)
Storage Temp: -20 to 85°C (-4 to 185°F)
Operating Temp: 0 to 65°C (32 to 149°F)
Sealing: IP67
Vibration (Sinusoidal Frequency):
10 to 50 Hz: 1 to 10 g rms linear Amplitude
50 Hz to 1 kHz: 10 g rms Amplitude
Shock:
Drop Testing: 1 m (3') onto hard surface
Topple Testing: 10 times each end onto hard surface
Case Material: 300 SS
Cable: PFA, 2 m (6') long
Core Material: Nickel-iron



I have a LD621-15 that I'm using to test Frequency Response of a Hydraulic actuator. I would like to knot what kind of latency (in Seconds or Fractions of a second) there is in the internal electronics of the output signal?
Thank you for you inquiry. Unfortunately there is no data available on the lag between movement to the rod and signal response of the LD621
Date published: 2021-07-26
Is this model spring-loaded? If so, in which direction (i.e. does it always try to stay extended, or retracted)?
Yes it is spring-loaded in the extended position
Date published: 2021-05-25
we have a couple LD621-5's on the shelf and would like to verify if they are good, is there a good procedure to do this with multimeter?
Thank you for your inquire
Best is to energize the unit and stretch-out the 5 mm and you should get a 10 volt output.
Hope this was helpful
Date published: 2022-01-14
Accessories